Site Loader

How to Keep Your Car Running Smoothly

Taking careful care of your vehicle is essential to ensure its performance. Besides, it is also beneficial to avoid costly repairs. In this case, proper and regular car maintenance is necessary to keep your vehicle in top condition. You can keep your car looking new by using spray ceramic coating instead of the usual one. However, there are other things you have to do to keep your vehicle running smoothly. Thus, follow these tips to help you keep your car in top shape before it costs you high for more maintenance and repairs.

Do a Regular Service

For a car, regular service is necessary. In this case, you can change your car’s engine spark plugs regularly. It will make the air-fuel mixture more efficient and cleaner. Also, be sure to check your oil. Your engine will work harder if there is less oil in it. 

As recommended by the manufacturer, change the filters every two months. Filters also need to be clean because dirty filters can cause your car to use ten percent more fuel. Make sure to align your tires properly by checking your tires regularly. To avoid unexpected problems, keep your vehicle in good condition. Otherwise, you may end up with low gas mileage due to damaged spark plugs and other issues.

porsche

Be Attentive to Your Driving Style

Drive slowly and carefully. It will help you apply the brakes slowly and avoid panic stops. If it is cold outside, allow your vehicle to warm up before driving. Drive slowly for the first 5-10 minutes to enable the engine oil to warm up and start lubricating all components.

Pay Attention to Engine Warning Signs

It is possible to drive short distances while some warning lights are on in a normal range. However, do not ignore three warning lights dealing with the engine temperature gauge, the brake light, and the engine oil light. You should check these warning lights and stop the engine as soon as possible. Indeed, you have to talk to your mechanic immediately.

Unload Extra Weight

car runningUnloading extra weight is critical to the proper operation of your car. The additional weight can put pressure on critical areas and cause premature wear. Thus, do not forget to remove parts that create extra resistance. That additional weight can not only aggravate your engine but also reduce fuel mileage.

Fix Problems as Soon as Possible

It is necessary to have your car checked as fast as possible if you notice a small problem. For example, a cracked CV boot is a common problem that needs to get fixed. Note that it is crucial to get it fixed immediately. Otherwise, you will be stuck and have to pay more.

Regular maintenance would help enhance your car’s performance. With these tips, you can make sure your vehicle is running well. Suppose it needs a repair. These maintenance tips can indeed save more money in your pocket when going to a mechanics’ help.

Tips on How to Repair Your Car’s Electric Window

repair toolsHere is what to do if the driver’s side electric window fails to operate properly or becomes trapped in a position. Before beginning your fix, be certain to have identified the issue. Make certain the glass is not jammed from the rubber clogs and seals. Ensure no physical harm to the wiring boot into the doorway is evident. If both front windows don’t function, then the error is most likely not from the ECM aka the Electric Window Module. You’ll require the best soldering iron to complete this fix.

Disassembling the ECM

You’ll have to take out the plastic cover under the steering column casing then remove the ECM’s cover. You’ll have to have some skill with a soldering iron, such as eliminating old solder and re-soldering existing joints. The positioning of this ECM is exposed after disassembling the plastic panel that covers the fuses. The ECM is cut on a plastic backplate that’s clipped onto the side of the heater. Removal may wreck the plastic clips, but that can easily be corrected later. The different lower wiring connectors could be pulled off. Remove the ECM wiring plug to expose the ECM in the automobile; notice that the plug-in has a locking clip.

Repairing the ECM

solderingThe ECM is the printed circuit board with parts on one side and the solder joints and paths on the opposite. If these exist, there could be a related track burn or soldering mistake which may be repaired. A normal dry joint is revealed close to the middle and is the most frequent fault.

There might be more than just one dry joint. As soon as you find it, then it could be required to remove the old solder and then clean it up until re-soldering the joint using a flux-cored solder. Re-assemble the ECM and give it a try by simply plugging it back. When the ECM functions match it back into place, with a tie-wrap when the backplate clips have died.…

Search

Terms and Privacy

valvoline